The article in the next paragraphs in relation to Installing A Bathtub is highly attention-grabbing. You should investigate it.
Installing a bathtub isn't specifically rocket science, however it does require strong plumbing, carpentry, as well as sometimes, tiling abilities. Changing an old bath tub with a new one is likewise a moderately difficult project. If the old bathtub is readily obtainable, the task can move easily; if you need to open a wall surface to remove the old tub and also position the new bathtub, the job is a lot harder. In either case, the task is within a home handyman's skills, although you will certainly require a helper to vacate the old bathtub and also embeded in the brand-new one. Make certain you have actually certified on your own for the work and also fit trying it. As opposed to working with a professional to take over a halfway-completed project, it is much better to take into consideration using one prior to you begin. Chances are you might require an expert plumber to make tube links.
This article will help you install a new bath tub in your bathroom if you have actually currently bought a brand-new tub as well as do not need to transform the setup of your previous water supply pipes.
Your tools as well as material list need to consist of the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is disconnect the supply of water. After doing so, turn on the taps to drain any kind of water remaining in the system. The procedure of getting rid of the existing faucets can be quite troublesome due to the restricted accessibility that is often the instance.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the taps. Have a fabric all set for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been eliminated, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from turning during this procedure. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any old securing compound.
Before carrying on to fit the new faucets, contrast the pipeline connections on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will certainly need a plastic connector to avoid damages to the thread. One end of the connector fits on the plastic tail of the tap and also the other end provides a link to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin guaranteeing that the washing machines remain in area in between the tap and also the sink. Secure the faucet in place with the manufacturer provided backnut. Once the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal tap ports. The former kind must be linked to the faucet ends first, tightening only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Setting up the Tub
Using both wood boards under its feet, place the bathtub in the needed position. The wooden boards are valuable in evenly spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto four small factors.
The next objective is to make certain that the bathtub is leveled all round. This can be attained by inspecting the spirit level as well as changing the feet on the bathtub until the level reviews degree.
To mount faucets, fit the bottom of the furthest flexible tap adapter to the ideal supply pipe by making a compression sign up with; after that do the exact same for the other tap.
Activate the water supply as well as check all joints and also new pipework for leaks as well as tighten them if required. Fill the bath tub as well as likewise inspect the overflow electrical outlet as well as the normal electrical outlet for leakages.
Lastly, fix the bath paneling as explained in the producer's user's manual. Tiling and also sealing around the bath tub must wait up until the bathtub has actually been made use of at the very least when as this will settle it into its final setting.
Getting ready for the Installment
Firstly, the supporting framework provided with the bathroom must be fitted (if needed) according to the supplier's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is essential to make certain that if the faucet includes a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets unit to avoid pressure on the bathtub.
Fit the versatile faucet adapters to the bottom of both faucets utilizing 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you utilize all of the supplied washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its last placement.
Tiling Around the Bathtub
In the area where the bathroom satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is important as the installation can relocate sufficient to crack a rigid seal, causing the water to permeate the wall surface in between the bath and also the tiling, bring about difficulties with wetness and also possible leaks to the ceiling below.
You can choose from a range of coloured sealers to blend in your components and also installations. They are sold in tubes and also cartridges, as well as can sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of soaked newspaper or soft rope. Bear in mind to always fill up the tub with water before securing, to allow for the activity experienced when the tub remains in use. The sealer can crack fairly early if you do not take into consideration this motion prior to sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally quickly available on the marketplace. It is suggested to fit the floor tiles making use of water-resistant or water-proof adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
I recently found that blog entry on Installing A Bathtub while perusing the web. Those who appreciated our blog entry if you please make sure you remember to pass it around. I value reading our article about Installing A Bathtub.
Professional approach assured.